SEKURE Paradox Digiplex DGP-610 Przewodnik Instalacji Pobierz pdf (Strona 52)

48 Reference & Installation Manual

3.6.13 Beep Timer For Door Left Open Alarm

SECTION [012]

Enter any value between 001 and 255 to determine the number of seconds

the Access Alarm will beep. Default = 5 seconds.

3.6.14 Door Forced Open Access Alarm

SECTION [006]: OPTION [3]

When the Door Forced Open Alarm is disabled, the following sections are

also disabled:

Option [3] OFF=Door Forced Open Alarm is disabled

(default)

Option [3] ON=Door Forced Open Alarm is enabled

3.6.15 Door Forced Open Feedback

SECTION [004]: OPTIONS [7] AND [8]

Option [7] OFF=Door Forced Open Alarm is silent

Option [7] ON=Door Forced Open Alarm is audible (default)

If option [7] is enabled:

Option [8] OFF=Will beep as long as Door Forced Open Alarm is occurring

(default)

Option [8] ON=Door Forced Open Alarm follows Beep Timer. (section

[013])

3.6.16 Beep Timer For Door Forced Open Alarm

SECTION [013]

Enter any value between 001 and 255 to determine the number of seconds

the Door Forced Open Alarm will beep. Default = 5 seconds.

3.6.17 PIN Entry ON Keypad

SECTION [006]: OPTION [4]

If the Card and Code Access option is enabled in the EVO control panel,

users must present their access control card and then enter their PIN on

the EVO641R keypad to gain access. The PIN Entry on Keypad option

cannot be turned ON and will always be OFF.

4.1 DGP2-648BL Programming

4.1.1 Partition Display

Section [001] to [008]

You can program the LED keypad to display up to four partitions. Sections

[001] to [008] correspond to partitions 1 to 8. The LED numbers A1 to A4

are assigned values 001 to 004 (Figure 29). To assign a display number to

a partition, choose a section number from [001] to [008] and assign it a

value between 001 and 004 which represents LED numbers A1 to A4

respectively

Figure 28: .: Keypad Overview

Figure 29: : LED Partition Display

Do not assign the same display number to more than one section.

For example, you cannot assign value 002 to sections [003] and

[004]. The rejection beep will remind you that a selected display

number is already assigned to another section.

4.1.2 Zone Display

Section [101] To [196]

You can program the keypad to display up to a total of 48. Sections [101] to

[196] correspond to zones 1 to 96 respectively. These zones are displayed

on LED numbers 1 to 48 and are assigned values 001 to 048.

Do not assign more than one LED number to a zone. For example,

you cannot assign LED number 33 to zones 21 and 28. The

rejection beep will remind you that a selected LED number is

already assigned to another section.

Every time the [

CLEAR] key is pressed it will revert to the preceding

step, unless entering in data in which case it will erase the current

entry.

4.1.3 Section Reset

Section [040]

This section resets zone display sections [101] to [196] to default settings.

Enter [040] to perform the reset.

4.1.4 Confidential Mode

Section [009] Option [1]

In Confidential Mode all LEDs will turn off until either a button is pressed or

an access code is entered.

Option [1] OFF = Disabled (default).

Option [1] ON = Enabled.

Table 18: Door Forced Open Access Alarm

Section

[004] Option [7] Door Forced Open Alarm

Option [8] Door Forced Open Alarm

follows

[013] Beep Timer for Door Forced Open Alarm

[ENTER] Saves current data and exits current menu.

[

CLEAR] Erases current data entry or reverts to the preceding step.

Partition Lights: (A1, A2, A3 and A4)

ON = Partition armed

OFF = Partition disarmed

FLASH = Partition in alarm

Action Lights: (Access, Stay,

Force, Mem, Trbl and Prg)

Lights will illuminate according

to the status of the system.

Numerical Lights: (Zones)

ON = Open / breached

OFF = OK

FLASHES = Tamper / fire loop

“AC” Light:

ON = AC Power

OFF = Power failure

“Status” Light:

When green:

ON = All zones closed

OFF = Zone(s) open

FLASH = Exit Delay in progress

When red:

ON = All partitions armed

OFF = Partition disarmed

FLASH = Partition in alarm

Keypad will display the status

of all its assigned partitions.

Value: 001 002 003 004

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 63 64

Komentarze do niniejszej Instrukcji

Brak uwag

SEKURE Paradox Digiplex DGP-610 Przewodnik Instalacji Strona 52

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa SEKURE Paradox Digiplex DGP-610