SEKURE Paradox Digiplex DGP-610 Przewodnik Instalacji Pobierz pdf (Strona 40)

36 Reference & Installation Manual

15 Access Control: System Features

For details on connecting Access Control devices, refer to the “Digiplex

Access Control Module Reference & Installation Manual”.

Figure 19: Typical Access Control Installation*

Persons authorized to access the protected area are issued cards assigned

to user access codes programmed with an Access Level (see section 15.5)

and a Schedule (see section 15.6). The control panel determines whether

or not to unlock the door depending on the card’s schedule and access.

15.1 Common Access Control Terms

Access Alarm: A warning generated by the reader if an Access Door is

open past the programmed time or if it was opened without the proper

signal. This event is logged in the Event Buffer, but cannot be reported.

Access Card: A tag assigned to a user access code used to identify the

user to the Access Control system.

Access Denied: The system preventing access through an Access Door.

Access Granted: The system granting access through a protected door.

Burglar Alarm: An warning sent to the control panel if an armed zone in

the EVO security system has been breached. This event is logged in the

Event Buffer and can be reported to a monitoring station.

Door Left Open: Each Access Door is programmed with a period of time it

is allowed to stay open. An Access Alarm will be triggered after that period.

Forced Door: An Access Door was opened without an “Access Granted” or

“Request for Exit” signal, a silent or audible Access Alarm can be triggered.

Reader: An Access Control device (DGP-R910) located near an Access

Door that sends the information from an Access Card to the control panel.

Request for Exit: When a REX device (Paradoor 460) detects movement,

it sends a request-for-exit signal to the panel.

Valid Card: An Access Card presented to a reader during its assigned

Schedule and within its assigned Access Level.

15.2 Programming Overview

The following is the MINIMUM required to program Access Control:

1. Enable Access Control in section [3038] option [1].

2. Assign the Doors in sections [2201] to [2232].

3. Create the Access Levels in sections [2601] to [2615].

4. Create the Schedules in sections [2401] to [2432].

5. Set the Holidays in sections [2701] to [2712].

6. Program user access codes (see section 14 on page 34).

7. Program the Access Control Modules.

15.3 Enable Access Control

SECTION [3038]: OPTION [1]

(default = disabled) Enable to activate Access Control.

15.4 Door Numbering

SECTIONS [2201] TO [2232]

Each door monitored and controlled requires an Access Control Module

(DGP-ACM12) or an access keypad. The keypad or module is assigned to

the door in sections [2201] to [2232]. EVO supports up to 32 Doors.

15.5 Access Levels

SECTIONS [2601] TO [2615]

Access Levels determine which Doors a user can access. Each Access

Level is a combination of the Doors from sections [2201] to [2232]. They

are assigned to the users through their user access codes (refer to the

“System Manager’s Manual”). Sections contains four screens representing

the 32 Doors. Level 00 allows the user to access all.

15.6 Access Schedules

SECTIONS [2401] TO [2432]

Schedules consist of two programmable time periods called Interval A and

B. Enter the Start Time and the End Time in the first and second screen.

Select the days in which it is valid in the third screen. Option [8] represents

the programmed holidays. If enabled, users have access between the Start

Time and End Time during the holidays. An Interval cannot cross into

another day. Schedules are assigned to the users through their user access

codes (refer to the “System Manager’s Manual”). Primary Schedules 001 to

015 are programmed in sections [2401] to [2415] respectively. Secondary

Schedules 016 to 032 are programmed in sections [2416] to [2432]

respectively. Schedule 000 allows the user access at all times. Primary

Schedules can be assigned to user access codes. Secondary Schedules

are Backup Schedules.

15.7 Backup Schedules

SECTION [2501] TO [2532]

When an Access Card or user access code is used at an Access Door, the

control panel verifies whether it was used during its assigned Primary

Schedule. If there are linked schedules, it will verify them. The control panel

will verify up to 8 linked Schedules. Each Schedule from 001 to 032 can be

linked to another Schedule in sections [2501] to [2532]. In each section

enter the 3-digit Schedule number to link it.

15.8 Holiday Programming

SECTIONS [2701] TO [2712]

Holiday Programming identifies holidays. Each section from [2701] to

[2712] represents a month. Each section includes four groups of five to

eight options that represent the days of the month. Enable the options

representing the holidays.

15.9 Schedule Tolerance Window

SECTION [3039]

User access codes with ‘Add Tolerance Windows to Schedules’ enabled

have the number of minutes programmed in [3039] added before and after

their Schedule. Enter any value between 001 and 255 (default = 000) to determine Schedule Tolerance Window in minutes.

1 = Request for Exit Device (Paradoor)

2 = Door Contact

3 = Reader (DGP-R910 or DGP-R915) on

other side of the wall

4 = Access Control Module (DGP-ACM12)

5 = Locking Device

6 = Control Panel (EVO)

Level 01: [2601] 01 to 08 09 to 16 17 to 24 25 to 32

Level 15: [2615] 01 to 08 09 to 16 17 to 24 25 to 32

Section Start Time End Time Days

Schedule 001: [2401]

Schedule 032: [2432]

set as per

24hr. clock

set as per

24hr. clock

[1] = Sunday (S)

[2] = Monday (M)

[3] = Tuesday (T)

[4] = Wednesday (W)

[5] = Thursday (T)

[6] = Friday (F)

[7] = Saturday (S)

[8] = Holidays (H)

set as per

24hr. clock

set as per

24hr. clock

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 63 64

Komentarze do niniejszej Instrukcji

Brak uwag

SEKURE Paradox Digiplex DGP-610 Przewodnik Instalacji Strona 40

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa SEKURE Paradox Digiplex DGP-610