SEKURE Paradox Digiplex DGP-610 Przewodnik Instalacji Pobierz pdf (Strona 31)

EVO Control Panel 27

10 Dialer Options

10.1 Telephone Line Monitoring

SECTION [3036]: OPTIONS [1] AND [2]

When enabled, the system verifies the existence of the main telephone line

once every second. After each successful test, the Status LED on the

control panel flashes briefly. A line test failure occurs when the TLM detects

less than 3 volts for the period defined by the TLM Fail Timer (see section

10.1.1). If the line test fails, the control panel will generate one or more

conditions as defined by the TLM settings below, until it detects the

telephone line again. When the dialer detects a telephone ring, the TLM

test stops for 1 minute.

10.1.1 TLM Fail Timer

SECTION [3053]

(default = 016) If the TLM does not detect the existence of the main

telephone line for the time programmed in this section, the control panel will

generate the condition(s) defined by the TLM options (see section 10.1).

Enter any value between 016 and 255 (value is X2 seconds) into section

[3053]. Entering a value between 000 and 016 will set the TLM Fail Timer

to 32 seconds.

10.2 Tone/Pulse Dialing

SECTION [3036]: OPTION [4]

(default = enabled)

10.3 Pulse Ratio

SECTION [3036]: OPTION [5]

(default = enabled) When using Pulse dialing (see section 10.2), select one

of two Pulse Ratios. If the selected pulse ratio does not provide adequate

results, try the other one.

10.4 Busy Tone Detection

SECTION [3036]: OPTION [6]

(default = enabled) When enabled, the control panel immediately hangs up

if it receives a busy signal when it dials an outside number.

10.5 Switch To Pulse

SECTION [3036]: OPTION [7]

(default = disabled) When is enabled, the control panel switches from tone

dialing to pulse dialing on the fifth attempt to report events to the monitoring

station. The control panel continues to use pulse dialing until it establishes

communication. When the control panel switches to another monitoring

station telephone number, it returns to tone dialing and switches back to

pulse dialing on the fifth attempt.

10.6 Bell On Communication Fail

SECTION [3036]: OPTION [8]

(default = disabled) When enabled and the control panel fails to

communicate with the monitoring station when the partition is armed, the

control panel can enable the BELL output.

10.7 Keypad Beep on Successful Arm or Disarm Report

SECTION [3037]: OPTION [5]

(default = disabled) When enabled and a user arms or disarms a partition,

the keypad emits a beep tone to confirm that the monitoring station

received the arming or disarming report code.

10.8 Dial Tone Delay

SECTION [3037]: OPTION [7]

(default = disabled)

If more time is required, insert a 4-second pause into the desired telephone

number sequence (see section 9.4).

[1] [2] Feature When the line test fails

OFF OFF Disabled TLM disabled (default) .

ON OFF Trouble Only

The Communicator trouble appears in the

Trouble Display.

OFF ON

Alarm when

Armed

The Communicator trouble appears in the

Trouble Display. If the partition is armed, the

control panel generates an alarm.

ON ON

Silent Alarms

become Audible

The Communicator trouble appears in the

Trouble Display. The control panel switches

any triggered Silent Alarm zones or Silent

panic alarms to an audible alarm.

[4] ON Tone/DTMF format

[4] OFF Pulse dialing format

[5] ON North American pulse ratio of 1:1.5

[5] OFF European pulse ratio of 1:2

[7] ON If no dial tone is present, dialer hangs up after 32 secs.

[7] OFF If no dial tone is present, force dials after 3 secs.

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 63 64

Komentarze do niniejszej Instrukcji

Brak uwag

SEKURE Paradox Digiplex DGP-610 Przewodnik Instalacji Strona 31

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa SEKURE Paradox Digiplex DGP-610