SEKURE Paradox Digiplex DGP-610 Przewodnik Instalacji Pobierz pdf (Strona 27)

EVO Control Panel 23

9.2.10 Special Alarm Report Codes

9.2.11 System Trouble Codes

9.2.12 System Trouble Restore Codes

If the Telephone Line Monitoring (see section 10.1) is disabled, the control panel will

not transmit the TLM report code.

9.3 Report Arming and Disarming

These features identify when partitions should be armed or disarmed. It

allow the control panel to report changes from the schedule.

9.3.1 Arming and Disarming Report Schedules

Arming and Disarming Report Schedules identify the days and times that a

partition should be armed and disarmed. Each schedule consists of 2

programmable time periods called Intervals that determine the time span

and days when the partition should be armed or disarmed (see Figure 17).

Schedules are enabled when they are programmed.

Figure 17: Example of an Arming and a Disarming Report Schedule

Program the Start Time and End Time according to the 24-hour clock and

enable the options representing the desired Days for the desired partition.

When option [8] is enabled, access is permitted during the programmed

holidays (see section 15.8 on page 36).

[3928] Remote Disarm

partition disarmed with InTouch Voice-

Assisted Arm/Disarm Module (APR3-ADM2)

[3930]

Emergency Panic

(non-medical)

the panic keys [1] and [3] were pressed

(see section 8.6 on page 20)

[3931] Auxiliary Panic

the panic keys [4] and [6] were pressed

(see section 8.6 on page 20)

[3932] Fire Panic

the panic keys [7] and [9] were pressed

(see section 8.6 on page 20)

[3933] Recent Closing

an alarm is generated within the Recent

Close Delay (see section 9.10 on page 25)

[3934] Police Code

Confirmation of an alarm condition occurred

during the Police Code Timer’s delay (see

section 8.4 on page 19).

[3935]

Auto Zone

Shutdown

the control panel stops regenerating alarms

on a zone during the same armed period

(see section 4.6.1 on page 11)

[3936] Duress

a Duress enabled access code is keyed in

(see Appendix 3: Keypad Installation

Instructions on page 44)

[3937] Keypad Lockout

too many invalid codes entered

(see section 7.19 on page 17)

[3941] AC Failure

AC power not detected. Also, see Power

Fail Report Delay in section 9.11

[3942] Battery Failure

battery is disconnected or the battery

voltage is less than or equal to 10.5V

[3943] Auxiliary Supply

the aux power supply’s current is greater

than or equal to 1.1A

[3944]

Bell Output

bell output is disconnected or the current

is greater than or equal to 3A

[3945] Clock Loss panel time lost (see section 13.17)

[3946] Fire Loop Trouble tamper on a Fire Zone (see section 4.4)

[3947] TO [3949] Future Use

[3950] Bus Fault a module was removed from the combus

[3951] Module Tamper

tamper/wire fault on module (not a motion

detector) on the combus

[3952] ROM Check Error on-board Read-Only Memory trouble

[3953] Module TLM

TLM failure detected on Listen-In Module

(DGP-LSN4)

[3954]

Module Fail to

Communicate

DGP2-DVAC failed to communicate with

the monitoring station

[3955] Printer Fault Printer Module detected an error

[3956] Module AC Failure no AC power detected on a module

[3957]

Module Battery

Failure

battery on a module is disconnected or the

battery voltage is low

[3958]

Module Auxiliary

Failure

the AUX output on a module has

exceeded current limits

[3959] Future Use

[3960]

Wireless Trans-

mitter Low Battery

the battery voltage is low on a wireless

transmitter

[3961]

Wireless Module

Supervision Failure

this report code is global unless using the

Contact ID or SIA reporting formats

[3962] to [3964] Future Use

[3965] Fail to Com 1 Phone Number 1 failed to communicate*

[3966] Fail to Com 2 Phone Number 2 failed to communicate*

[3967] Fail to Com 3 Phone Number 3 failed to communicate*

[3968] Fail to Com 4 Phone Number 4 failed to communicate*

* No “Fail to Communicate” for Pager telephone numbers

[3970] TLM1 Restored [3981] Module Tamper Restored

[3971] AC Restored [3982] ROM Check Error Restored

[3972] Battery Restored [3983] Module TLM Restored

[3973]

Auxiliary Supply

Restored

[3984]

Module Fail to Communicate

Restored

[3974] Bell Output Restored [3985] Printer Fault Restored

[3975] Clock Loss Restored [3986] Module AC Failure Restored

[3976] Fire Loop Restored [3987] Module Battery Restored

[3977] Future Use [3988] Module Auxiliary Restored

[3978] Future Use [3989] Future Use

[3979] Future Use [3990]

Wireless Transmitter Battery

Restored

[3980] Bus Fault Restored [3991]

Wireless Module Supervision

Restored

Arming Report Schedule

Partition 1: [3102] Partition 3: [3302] Partition 5: [3502] Partition 7: [3702]

Partition 2: [3202] Partition 4: [3402] Partition 6: [3602] Partition 8: [3802]

Disarming Report Schedule

Partition 1: [3103] Partition 3: [3303] Partition 5: [3503] Partition 7: [3703]

Partition 2: [3203] Partition 4: [3403] Partition 6: [3603] Partition 8: [3803]

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 63 64

Komentarze do niniejszej Instrukcji

Brak uwag

SEKURE Paradox Digiplex DGP-610 Przewodnik Instalacji Strona 27

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa SEKURE Paradox Digiplex DGP-610