SEKURE Paradox Digiplex DGP-610 Przewodnik Instalacji Pobierz pdf (Strona 13)

EVO Control Panel 9

4 Zone Programming

Enter Section [0400], then

enter the number of the

zone you want to program

Enter the zone’s 8-digit

serial and 3-digit input

number (The input number

is not needed for module

with only one input)

Enter the zone’s parameters

(01) (*2*****) default

Enter the zone’s report

codes

(00) (00) (00) (00) default

Enter the zone’s label

Press [ENTER] to save and

go to the next zone

Pressing [CLEAR] twice will

exit the zone programming

menus. Press [ENTER]

before pressing clear to

save your modifications.

Zone Definition Partition Zone Option

_____ _____ 1 2 3 4 5 6 7 8

0 - Disabled (default)

1 - Entry Delay 1

2 - Entry Delay 2

3 - Follow

4 - Instant

5 - 24Hr Buzzer

6 - 24Hr Burglary

7 - 24Hr Hold-up

8 - 24Hr Gas

9 - 24Hr Heat

A - 24Hr Water

B - 24Hr Freeze

C - Delayed 24Hr

Fire

D - Standard 24Hr

Fire

E - Stay Delay 1

F - Stay Delay 2

1 - Assigned to Partition 1

(default)

2 - Assigned to Partition 2

3 - Assigned to Partition 3

4 - Assigned to Partition 4

5 - Assigned to Partition 5

6 - Assigned to Partition 6

7 - Assigned to Partition 7

8 - Assigned to Partition 8

[1] Auto Zone Shutdown Enabled

[2] Bypass Enabled (default)

[3] Stay Zone

[4] Force Zone

[5] [6] Zone Alarm Type

off off Steady Alarm

off on Pulsed Alarm

on off Silent Alarm

on on Report Only

[7] Intellizone

[8] Delay before Transmission

Ademco slow, Silent Knight fast, SESCOA, Ademco express or Pager formats:

Key-in desired 2-digit hex values from 00 to FF.

Ademco format:

Use section [4032] to program a set of default Ademco report codes from the Auto

Report Code Programming on page 26. Then to program the remaining report

codes or to change some of the defaults, enter the individual sections and key-in

the desired 2-digit hex value found in the Appendix 2: Contact ID Report Code List

on page 42.

SIA format:

Use section [4032] to program a set of SIA report codes from the Auto Report Code

Programming on page 26. Codes that have not been set to default can be set to

default manually by entering FF in the appropriate section. To disable the reporting

of an event, enter 00 in the appropriate section

Alarm Report Code

Alarm Restore

Report Code

Tamper Report

Code

Tamper Restore

Report Code

__ / __ __ / __ __ / __ __ / __

In any Zone Programming option, pressing [ACC] will save the data and go

to the next zone on the same option screen. Pressing [TRBL] will save the

data and go to the previous zone on the same option screen.

Input 2

Hardwired

Device B

Control Panel

SN#:020000A2

APR3-ZX8 Module

SN#: 34000041

Input 5

Detector A

SN#: 21000033

OMMUNICATION

ETWORK

Input Terminals

1 2 3 4 5 6 7 8

Detector A:

Hardwired Device A:

Hardwired Device B:

Hardwired Device C:

Zone#

1 =

2 =

3 =

4 =

Section#

[0001]

[0002]

[0003]

[0004]

Serial#

21000033

1A000252

020000A2

34000041

Input#

N/A

002

005

Keypad

SN#: 1A000252

Keypad Zone

Hardwired

Device C

Hardwired

Device A

Input Terminals

1 2 3 4 5 6 7 8

Combus

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 63 64

Komentarze do niniejszej Instrukcji

Brak uwag

SEKURE Paradox Digiplex DGP-610 Przewodnik Instalacji Strona 13

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa SEKURE Paradox Digiplex DGP-610