SEKURE Paradox Spectra 1686H Instrukcja Instalacji Pobierz pdf (Strona 27)

SPECTRA SERIES 25

be bypassed regardless of their definition (except 24hr. zones). Upon arming, the control panel will transmit the No

Movement report code if programmed in section [172]. Regardless of whether the system was successfully armed

or not, the control panel will always transmit the No Movement report code if programmed in section [172]. If No

Movement Auto-Arming is disabled, the control panel will still send the No Movement report code at the time

specified by the No Movement Timer.

Example: To arm partition 1 whenever there is no movement for a period of 4 hours, enable No Movement Auto-

arming for partition 1 by turning on the [2] Option in section [133]. Then in section [075] enter 016 (16x15min. =

240min. = 4 hours).

6.7.1 NO MOVEMENT TIM ER

Section [075] = Partition 1, [076] = Partition 2

001 to 255 x15min., Default = disabled

Select the section corresponding to the desired partition and program the interval of time without

movement you wish the control panel to wait before arming and/or sending the No Movement report code.

If No Movement Auto-Arming is disabled, the control panel can still send the No Movement report code

when no movement has been detected for the period specified by the No Movement Ti mer.

6.8 AUTO-ARMING OPTIONS

Section [133] = Partition 1, [134] = Partition 2

Option [3] OFF = Regular Arming (default)

Option [3] ON = Stay Arming

When using Timed Auto-Arming or No Movement Auto-Arming (see section 6.6 and section 6.7), the control panel

can Regular or Stay Arm (see page 48) the selected partition. This feature is not to be used with UL installations.

6.9 ONE-TOUCH ARMING

Section [130 ]: Options [1] to [4]

Option [1] ON = Press & hold the [ENTER ] key for One- touch Regular Arming.

Option [2] ON = Press & hold the [STAY] key for One-touch Stay Arming.

Option [3] ON = Press & hold the [FORCE] key for One-touch Force Arming.

Option [4] ON = Press & hold the [BY P] key for One-touch Bypass Programming.

The One-touch Arming features allow users to arm the system without having to enter any access codes. To arm the

system, press and hold the appropriate key (see above) for approximately 2 seconds. If the system is partitioned

(see page 39), you must also press the key corresponding to the partition you wish to arm. For more information on

the different arming methods, please refer to page 48. This feature is not to be used with UL installations

6.10 EXIT DELAY

Section [071] = Partition 1, [072] = Partition 2

001 to 255 seconds, Default = 30 seconds

After entering the required arming sequence (i.e. User Access code, etc.), the Exit Delay parameter determines the

amount of time a user has to leave the protected area before the control panel arms the partition. The Exit Delay

applies to all zones in the selected partition. When enabled, the keypad will beep once every second during the Exit

Delay and wi ll beep rapidly duri ng the final 10 seconds of the Exit D elay. Max 60 seconds for UL listed systems.

6.10.1 BEEP ON EXIT DEL AY

Section [130]: Arming/Disarming Options

Option [8] OFF = Beep on Exit Delay Disabled

Option [8] ON = Beep on Exit Delay Enabled (default)

6.11 BELL SQUAWK ON ARM/DISARM WITH KEYPAD

Section [130 ]: Arming/Disar min g Options

Option [7] OFF = Bell Squawk on Arm/Disarm Disabled (default)

Option [7] ON = Bell Squawk on Arm/Disarm Enabled

When this feature is enabled, the bell or siren will squawk once upon arming and twice upon disarming.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 59 60

Komentarze do niniejszej Instrukcji

Brak uwag

SEKURE Paradox Spectra 1686H Instrukcja Instalacji Strona 27

Komentarze do niniejszej Instrukcji