SEKURE Paradox Spectra 1686H Instrukcja Instalacji Pobierz pdf (Strona 14)

12 REFERENCE & INSTALLATION MANUAL

3.3 CONFIGURING THE LED KEYPADS

Depending on the version of the keypad, two methods can be used to configure the LED keypads (1686H, 1686V

and 1689):

3.3.1 CONFIGURING THE 1686H, 1686V AN D 1689 KEYPADS V2.0 OR HIGHER

The keypad’s zone number, EOL definition and tamper switch are programmed through the control panel’s

programmi ng mode. To do so:

PLEASE NOTE: After two minutes, the keypad exits programmin g mode.

Key [1] - Keypad Zone Selection

Key [1] determines whether the keypad’s zone is Keypad Zone 1 or Keypad Zone 2. When key [1] is OFF

(not illuminated), the keypad’s zone is Keypad Zone 1. When key [1] is ON (illuminated), the keypad’s zone

is Keypad Zone 2. Refer to Table 4 on page 16 for more information.

Key [1] OFF - Keypad Zone 1 (default)

Key [1] ON - Keypad Zone 2

Key [2] - EOL Definition

Key [2] determines the keypad zone’s EOL definition. When key [2] is OFF (not illuminated), EOL is

disabled and the keypad zone will use the on-board EOL resistor. When key [2] is ON (illuminated), EOL is

enabled and the keypad zone requires that an external EOL resistor be connected (refer to Spectra

1738EX and 1738 Control Panel Overview on page 4 and Spectra 1728EX and 1728 Control Panel

Overview on page 5 for more details).

Key [2] OFF - EOL disabled

Key [2] ON - EOL enabled (default)

Key [3] - On-Board Tamper

Key [3] enables or disables the keypad’s on-board tamper switch. When key [3] is OFF (not illuminated),

the tamper switch is disabled. When key [3] is ON (illuminated), the tamper switch is enabled.

Key [3] OFF - On-board tamper switch disabled

Key [3] ON - On-board tamper switch enabled

PLEASE NOTE: The keypad can be ordered with or without a tamper switch. If the keypad has

no tamper switch, key [3] will be OFF by default. If the keypad has a tamper switch, key [3]

will be ON by default.

3.3.2 CONFIGURING THE 1686H, 1686V AN D 1689 KEYPADS PRIOR TO V2.0

The keypad’s zone number and EOL definition are defined through the jumpers located on the PCB board.

The jumpers are as follows:

J1 - Keypad Zo ne Select J umper

Jumper J1 determines whether the keypad’s zone is Keypad Zone 1 or Keypad Zone 2. When the jumper

is OFF, the keypad’s zone is Keypad Zone 2. When the jumper is ON, the keypad’s zone is Keypad Zone 1.

Refer to Table 4 on page 16 for more information.

J1 OFF - Keypad Zone 2

J1 ON - Keypad Zone 1

How Do I Configure The Keypad?

STEP 1: Press [ENTER]

STEP 2: Enter your [INSTALLER CODE] (default: 000000 or 0000)

STEP 3: Pr ess the [PG] (1686H /V) / [FN C 1] (1689) key and hold i t for 3 seconds.

STEP 4: Press the desired key ([1] to [3]. See below)

STEP 5: Press [ENTER] to exit programming mode

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 59 60

Komentarze do niniejszej Instrukcji

Brak uwag

SEKURE Paradox Spectra 1686H Instrukcja Instalacji Strona 14

Komentarze do niniejszej Instrukcji