SEKURE DGP2-641 Instrukcja Instalacji Pobierz pdf (Strona 19)

IGIPLEX

NE C

ONTROL

ANEL

5.2 Z

ONE

OUBLING

(ATZ)

(Default = disabled) The ATZ feature is a software oriented feature that

enables two detection devices to be installed per hardwired input terminal

(section 3.15 on page 13 and see section 3.14 on page 13). Each detection

device has its own zone, displays its zone status on the keypad and sends

its own alarm codes. Fire Zones cannot be doubled.

5.3 Z

ONE

EFINITIONS

The 16 zone definitions from Figure 5-1 on page 16 are described below.

When an alarm occurs, the control panel can send a report, activate the bell

output and display the alarm in the Alarm Memory.

5.3.1 Zone Disabled

Disables the corresponding zone. Zones are disabled by default.

5.3.2 Entry Delays 1 and 2

(Default Entry Delay 1= 030, Entry Delay 2 = 060) When an armed zone

defined as an Entry Delay opens, the control panel will not generate an

alarm until the Entry Delay Timer elapses. A zone defined as Entry Delay 1

follows the Entry Delay 1 Timer of its assigned partition. Likewise, a zone

defined as Entry Delay 2 follows the Entry Delay 2 Timer of its assigned

partition.

For example, if zone 1 is assigned to Partition 5 and is defined as Entry

Delay 1, the timer follows the amount programmed in [3511].

Each partition includes two Entry Delay Timers. To program an Entry Delay

Timer, key in the desired 3-digit delay value (001 to 255 seconds) into the

corresponding section.

Entry Delay zones are commonly used at the entry/exit points (i.e. front/

back door or garage). Using different Entry Delays is useful when one entry

point requires a longer delay than another.

These are the same timers used for Stay Delay zones (see section

5.3.14).

5.3.3 Follow Zones

If an armed Follow zone opens, the control panel generates an alarm. If an

armed Entry Delay zone (see section 5.3.2) opens before the Follow zone,

the control panel waits until the end of the Entry Delay before generating an

alarm. If more than one Entry Delay zone opens before the Follow zone,

the control panel waits until the end of the first Entry Delay before

generating an alarm. This feature is commonly used when a motion

detector is protecting the area occupied by the entry point keypad. This will

prevent the motion detector from causing an alarm when a user enters

through the entry point to disarm the system.

5.3.4 Instant Zones

When an armed Instant zone opens, the control panel immediately

generates an alarm. Instant zones are commonly used for windows, patio

doors, skylights and other perimeter type zones.

5.3.5 24Hr Buzzer Zones

Whenever a 24Hr Buzzer zone opens, whether the zone is armed or

disarmed, the control panel activates the keypad buzzer to indicate that the

zone was breached. The control panel will report the alarm, but will not

enable the bell/siren output. Enter any valid access code on the keypad to

stop the buzzer.

The keypads must be assigned to the same partition as the

24Hr Buzzer zone or the buzzer will not activate.

5.3.6 24Hr Burglary Zones

When a 24Hr Burglary zone opens, whether the system is armed or

disarmed, the control panel will immediately generate a burglary alarm.

5.3.7 24Hr Hold-up Zones

When a 24Hr Hold-up zone opens, whether it is armed or disarmed, the

control panel will immediately generate an alarm. The SIA FSK reporting

format includes specific codes to identify the alarm as a Hold-up Alarm.

5.3.8 24Hr Gas Zones

When a 24Hr Gas zone opens, whether it is armed or disarmed, the control

panel will immediately generate an alarm. The SIA FSK reporting format

includes specific codes to identify the alarm as a Gas Alarm.

5.3.9 24Hr Heat Zones

When a 24Hr Heat zone opens, whether it is armed or disarmed, the control

panel will immediately generate an alarm. The SIA FSK reporting format

includes specific codes to identify the alarm as a Heat Alarm.

5.3.10 24Hr Water Zones

When a 24Hr Water zone opens, whether it is armed or disarmed, the

control panel will immediately generate an alarm. The SIA FSK reporting

format includes specific codes to identify the alarm as a Water Alarm.

5.3.11 24Hr Freeze Zones

When a 24Hr Freeze zone opens, whether it is armed or disarmed, the

control panel will immediately generate an alarm. The SIA FSK reporting

format includes specific codes to identify the alarm as a Freeze Alarm.

5.3.12 Delayed 24Hr Fire Zone

The Delayed 24Hr Fire Zone definition from Figure 5-3: on page 18 is

commonly used in residential homes where a smoke detector often

generates false alarms (i.e. cigarette smoke, burning bread, etc.). A zone

programmed as Fire becomes normally open (will not function as normally

closed) and requires an EOL resistor.

Input Doubled Zone Input

Input 01 Input 13 (ATZ of Input 01)

Input 02 Input 14 (ATZ of Input 02)

Input 03 Input 15 (ATZ of Input 03)

Input 04 Input 16 (ATZ of Input 04)

Input 05 Input 17 (ATZ of Input 05)

Input 06 Input 18 (ATZ of Input 06)

Input 07 Input 19 (ATZ of Input 07)

Input 08 Input 20 (ATZ of Input 08)

Input 09 (DGP2-ZX4 Input 01) Input 21 (ATZ of Input 09)

Input 10 (DGP2-ZX4 Input 02) Input 22 (ATZ of Input 10)

Input 11 (DGP2-ZX4 Input 03) Input 23 (ATZ of Input 11)

Input 12 (DGP2-ZX4 Input 04) Input 24 (ATZ of Input 12)

Partition 1

Entry Delay 1 Timer: [3111]

Entry Delay 2 Timer: [3112]

Partition 5

Entry Delay 1 Timer: [3511]

Entry Delay 2 Timer: [3512]

Partition 2

Entry Delay 1 Timer: [3211]

Entry Delay 2 Timer: [3212]

Partition 6

Entry Delay 1 Timer: [3611]

Entry Delay 2 Timer: [3612]

Partition 3

Entry Delay 1 Timer: [3311]

Entry Delay 2 Timer: [3312]

Partition 7

Entry Delay 1 Timer: [3711]

Entry Delay 2 Timer: [3712]

Partition 4

Entry Delay 1 Timer: [3411]

Entry Delay 2 Timer: [3412]

Partition 8

Entry Delay 1 Timer: [3811]

Entry Delay 2 Timer: [3812]

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 65 66

Komentarze do niniejszej Instrukcji

Brak uwag

SEKURE DGP2-641 Instrukcja Instalacji Strona 19

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa SEKURE DGP2-641