SEKURE DGP2-648 Instrukcja Instalacji Pobierz pdf (Strona 30)

28 REFERENCE & INSTALLATION MANUAL

8.8.1 Maximum Dialing Attempts**

SECTION [3056]

(Default = 008) The number (001 to 255, 000 = 8 attempts) programmed

into section [3056] determines how many times the control panel will dial

the same Monitoring Station Telephone Number before proceeding to the

next number. Also refer to section 8.8.3.

** UL Note: For UL Listed systems, the maximum dialing attempts must be

set to 5 to 10 attempts between the DGP-NE96’s two telephone lines.

8.8.2 Delay Between Dialing Attempts

SECTION [3054]

(Default = 020) This delay will determine the amount of time the control

panel will wait between dialing attempts. This delay can be set from 001 to

127 seconds.

8.8.3 Alternate Dialing Option

SECTION [3037]: OPTION [6]

(Default = disabled) With option [6] enabled in section [3037], the control

panel dials the selected backup telephone number after every failed

attempt to contact a Monitoring Station Telephone Number. Otherwise

(option [6] off), the control panel only dials the backup telephone number

after the Maximum Dialing Attempts (see section 8.8.1) to one Monitoring

Station Telephone Number fail.

8.9 PAGER DELAY

ECTION [3057]

(Default = 060) When using the Pager Reporting Format (see section

8.7.6), the control panel will wait for the delay period programmed into

section [3057] before uploading the report codes to the pager. This is to

allow time for the pager system to provide a dial tone or to bypass the

welcome message before sending the data. Enter any value between 001

and 127 to determine Pager Delay in seconds.

8.10 RECENT CLOSE DELAY

(Default = 000) If, after arming the partition, an alarm is generated within

the programmed period, the control panel will transmit the Recent Close

report code programmed into section [3933]. Enter any value between 001

and 255 to determine Recent Close Delay in seconds.

8.11 POWER FAILURE REPORT DELAY

ECTION [3058]

(Default = 030) The control panel will delay the transmission of the AC

Failure report code programmed into section [3941] by the period

programmed into section [3058]. Enter any value between 001 and 255 to

determine Power Failure Report Delay in minutes.

8.12 AUTO TEST REPORT

ECTION [3037]: OPTION [3] AND [4] AND

ECTIONS [3040], [3041], [3042] AND [3043]

The control panel can transmit the test report code programmed into

section [3902] every hour (Hourly Test Transmission) or after a period of

time (Auto Test Report Period).

8.13 DISARM REPORTING OPTIONS

(Default = disabled) When option [7] is disabled, the control panel sends

the Disarming Report Codes (see section 8.2) every time the partition is

disarmed. When option [7] is enabled, the control panel sends the

Disarming Report Codes to the Monitoring Station only when the partition is

disarmed following an alarm. Select the section that corresponds to the

desired partition and enable or disable option [7]:

8.14 ZONE RESTORE REPORT OPTIONS

ECTION [3037]: OPTION [8]

(Default = disabled) When option [8] is disabled, the control panel sends

the Zone Alarm Restore report codes to the Monitoring Station when the

Bell Cut-Off Timer elapses (see section 7.2) or when the alarm is disarmed.

When option [8] is enabled, the control panel sends the Zone Alarm

Restore report codes (see section 8.2) to the Monitoring Station as soon as

the zone returns to normal (zone closure) or upon disarming.

8.15 AUTO REPORT CODE PROGRAMMING

When using either the Contact ID or SIA Reporting Formats (see section

8.7), the control panel can automatically program a set of default report

codes. However, the Contact ID Reporting Format can be modified using

the manual programming method (see section 8.7.4 & section 8.7.5) to

program remaining report codes or to change some of the defaults. From

programming mode (see section 3.4) enter any of the following sections to

set the indicated report codes with the default values (FF) from the

Automatic Report Codes List in the Programming Guide:

[3] Telephone Number 3 [7] Backup on Number 3

[4] Telephone Number 4 [8] Backup on Number 4

Partition 1: [3109] Partition 3: [3309] Partition 5: [3509] Partition 7: [3709]

Partition 2: [3209] Partition 4: [3409] Partition 6: [3609] Partition 8: [3809]

Option Feature Description

[3] [4]

OFF OFF

Auto Test

Report

Period

(default)

After the number of days (000 to 255, default =

000) programmed into section [3040] elapse, the

control panel can transmit the report code at the

time (00:00 to 23:59, default = 00:00)

programmed into section [3041].

ON OFF

Hourly Test

Transmission

The control panel transmits the test report code at

the same time every hour. Program the minute of

each hour (00:00 to 00:59, default = 00:00) when

the test report should be sent into section [3041].

ON ON

Timed Test

Transmission

when Armed/

Disarmed

When armed: The control panel transmits the test

report code at regular intervals while the partition

is armed. Program the number of minutes (000 to

255, default 005) between each transmission in

section [3042].

When disarmed: The control panel transmits the

test report code at regular intervals while the

partition is disarmed. Program the number of

minutes (000 to 255, default = 060) between each

transmission in section [3043].

Partition 1: [3123] Partition 3: [3323] Partition 5: [3523] Partition 7: [3723]

Partition 2: [3223] Partition 4: [3423] Partition 6: [3623] Partition 8: [3823]

Section Description

[4030] Resets all the report code sections to 00 (cleared).

[4031] Sets all the report code sections to FF (defaults).

Section Sets to Defaults (FF) Reset Sections

[4032]

Zone Alarm and Restore Report Codes

Tamper and Restore Report Codes

[0201] to [0296]

[4033]

Keyswitch Arming Report Codes

Keyswitch Disarming Report Codes

Access Code Arming Report Codes

Access Code Disarming Report Codes

[0701] to [0732]

[0801] to [0832]

[2001] to [2099]

[2101] to [2199]

[4034] Special System Report Codes [3900] to [3909]

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 63 64

Komentarze do niniejszej Instrukcji

Brak uwag

SEKURE DGP2-648 Instrukcja Instalacji Strona 30

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa SEKURE DGP2-648