SEKURE DGP2-648 Instrukcja Instalacji Pobierz pdf (Strona 19)

DIGIPLEXNE CONTROL PANEL 17

5.2.4 Generates a Utility Key Event on Open

SECTIONS [0601] TO [0632]: FIRST DIGIT = 3

When option [3] is enabled, a Utility Key Event will be generated whenever

the keyswitch input is opened (see Table 14 on page 51). This option can

be used to activate or deactivate one or more of DigiplexNE’s PGM outputs.

When a keyswitch is defined with the Generate a Utility Key Event on Open

option, the Keyswitch Partition Assignment and Keyswitch Options are

disabled. To program a Keyswitch to generate a Utility Key Event:

1) Program the Activation Event of a PGM output with the Utility Key

Event corresponding to the desired keyswitch (see PGM

Programming Table in the Programming Guide: Event Group 048).

2) Enable option [3] in the section corresponding to the desired

keyswitch.

5.2.5 Generates a Utility Key Event on Open and Close

SECTIONS [0601] TO [0632]: FIRST DIGIT = 4

When option [4] is enabled, a Utility Key Event will be generated whenever

the keyswitch input is opened and closed. As a result, the Utility Key Events

increase from 32 to 64 events when option [4] is enabled; one event for

each state (open and closed). See Table 14 on page 51.

This option can be used to activate or deactivate one or more of

DigiplexNE’s PGM outputs. When a keyswitch is defined with the Generate

a Utility Key Event on Open and Close option, the Keyswitch Partition

Assignment and Keyswitch Options are disabled. To program a Keyswitch

to generate a Utility Key Event:

1) Program the Activation Event of a PGM output with the Utility Key

Event corresponding to the desired keyswitch (see PGM

Programming Table in the Programming Guide: Event Group 048).

2) Enable option [4] in the section corresponding to the desired

keyswitch.

5.3 KEYSWITCH PARTITION ASSIGNMENT

ECTIONS [0601] TO [0632]: SECOND DIGIT = 1 TO 8

The control panel provides the option of partitioning the security system into

eight completely independent systems. Therefore, each keyswitch must be

assigned to one partition as shown in Figure 5-1 on page 16. For details on

Partitioning, see section 11.9 on page 32.

5.4 KEYSWITCH OPTIONS

Each keyswitch zone can be programmed with one or more of the options

below as shown in Figure 5-1 on page 16.

5.4.1 Stay/Instant Disarm Option (Keyswitch)

SECTIONS [0601] TO [0632]: OPTION [4]

When option [4] is enabled, the keyswitch can only disarm assigned Stay or

Instant Armed partitions. The Arm Only Option (see section 5.4.2) must be

disabled for this feature to function. When option [4] is disabled, the

keyswitch can disarm partitions armed using any arming method.

5.4.2 Arm Only (Keyswitch)

SECTIONS [0601] TO [0632]: OPTION [5]

When option [5] is enabled, the keyswitch can arm assigned partitions, but

cannot disarm any partitions. The type of arming is determined by the other

Keyswitch Options selected.

5.4.3 Regular Arming (Keyswitch)

SECTIONS [0601] TO [0632]: OPTION [6] TO [8]

When options [6] to [8] are disabled, the keyswitch arming option will

default to Regular Arming (see section 15.1).

5.4.4 Stay Arming (Keyswitch)

SECTIONS [0601] TO [0632]: OPTION [6]

Activating the keyswitch will bypass any zones defined as Stay Zones (see

section 4.5.3) in the selected partition. All other zones will remain activated.

For more information on Stay Arming, refer to section 15.2.

5.4.5 Force Arming (Keyswitch)

SECTIONS [0601] TO [0632]: OPTION [7]

Activating the keyswitch will arm the selected partition bypassing any open

zones defined as Force Zones (see section 4.5.4) at the time of arming. For

more information on Force Arming, refer to section 15.4.

5.4.6 Instant Arming (Keyswitch)

SECTIONS [0601] TO [0632]: OPTION [8]

This option is identical to Stay Arming except that all armed zones will

become Instant Zones (see section 4.3.4). For more information on Instant

Arming, refer to section 15.3.

Only one of the arming options (Stay, Force, Instant and Regular)

can be selected.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 63 64

Komentarze do niniejszej Instrukcji

Brak uwag

SEKURE DGP2-648 Instrukcja Instalacji Strona 19

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa SEKURE DGP2-648